Fit Brand New Kubota Engine V1505-E3B-CWL-1 / CT04 Model 1J904-71000 Motor

  
BUILT TO SPEC, BUILT TO LAST. During the manufacturing process our suppliers source the highest quality materials and use only upgraded parts. Our new engines are always built to spec and built to last. We ensure correct fitment for all vehicles that match the year make and model advertised in the listing title. These engines come as bare blocks with very little (if any) external accessories. Please reapply all of your original accessories to ensure fitment and compatibility. When purchasing our engines, there is no core charge ever! Guarantee: 6 Months engine size: 1.5L fuel type: Diesel number of valves: 16 number of cylinders: 4-Cylinder performance : Non Turbo compression ratio : 23.1 bore diameter mm : 78.0 maximum horsepower ps : 44.3 maximum power kw : 26.1 maksimum power speed rpm : 3000 make : Kubota model : V1505 displacement : 1.5L maximum torque n m : 118.6 maximum torque speed rmp : 2000 dimension : 31 x 20 x 33 inch. With our expansive LTL network you will get the best turn around time and service available to your region. This number will be unique to the individual claim and must be obtained before any return whatsoever, no exceptions. Electronics such as, but not limited to, ECU's, sensors, and wiring harnesses are not refundable unless noted. Once the item has been tampered with or opened, the item is no longer refundable. Covered Components: The following components are covered in gasoline or diesel engines: pistons, piston pins, piston rings, crankshaft and main bearings, connecting rods and rod bearings, camshaft bearings, intake and exhaust valves, valve springs, push rods, rocker arms and rocker arm shafts. Block and Heads: The engine block and cylinder heads are covered only if damaged by Covered Components.

Replacement Parts: In case of a defect or failure of our engine, our obligation is limited to repairing or replacing damaged, defective, or broken Covered Components as set forth above. Installation done by certified ASE shop during the 30 day installation window which begins the day this item is delivered and signed for.

Reattachment of all accessories, emissions, and external components from original engine as per factory specifications and operating standards. Install new timing belt, water pump tensioner on belt driven engines. For chain driven engines: New, dry, timing chain engines will have a clicking noise.

This is a normal timing chain noise. Prime the engine with oil prior to start to ensure oil build up and proper internal lubrication of all covered components prior to operating the engine.

Breaking in a new engine is a way to condition the engine&#####x2019;s internal components for its role in the overall life of the vehicle. In particular, this &#####x201C;breaking in&#####x201D; allows the piston&#####x2019;s rings to properly mate up to the cylinder&#####x2019;s walls, preventing long-term wear that could lead to oil consumption, poor performance, or both. Typically, an engine&#####x2019;s break-in period is within the first 500 to 1,000 miles.

Pushing the engine too hard early on&#####x2014;which might be enticing if it&#####x2019;s a sports car or other performance vehicle&#####x2014;may cause certain engine components to not seat correctly, like the piston rings, rod bearings, or other crucial parts of its overall function. The key is to be gradual and patient. Driving the car gently during these initial miles helps ensure minimal premature wear. The easiest way to break in an engine is to simply take it easy. Keep it spinning under 4,000 rpm (revolutions per minute, as indicated on the tachometer in the gauge cluster) within the first 500-1,000 miles.

After that, revving up the engine higher should be fine. If the car has a manual transmission, make sure to keep the shifts low in the rev band, which is often referred to as short-shifting. Hard acceleration early puts too much strain on the piston rings and cylinders, which could shorten the engine&#####x2019;s overall life.

Perform 500 mile engine maintenance check up. Change engine oil and filter. After this continue with oil changes regularly at factory recommended intervals. The vehicle is converted from a private passenger use to commercial or fleet use, or is used for racing or other competition or off-road recreational purposes. Failure is caused by abuse, misuse, or modifications. Removal of heads/permanent modification of any kind outside of factory setting.

The part fails or becomes defective due to the vehicle being involved in a collision. The part is installed or operated outside the United States.

Defects or failures caused by overheating (heat tab bulging or melting). Defects or failures caused by lack of lubrication (running out of oil and coolant).

Camshaft lobe or lifter wear on flat lifters. Detonation of a piston &#####x2013; burned pistons or holes in pistons. Defects or failures caused by dirt found in assembly. Damaged or leaking gaskets, seals, or fittings. Defects or failures caused by lack of proper break-in procedures and break-in oil.

Defects or failures caused by storage of engine &#####x2013; Nonuse. Any field labor or expenses. This means we do not pay labor, parts, or costs for your engine to be repaired, worked on, evaluated, or reviewed at another facility. Defects or failures caused by over-revving, accident, abuse, or an operation for which I was not designed. Defects or failures caused by alteration of either the drive train or the suspension from the original manufacturers&#####x2019; specifications. Defects or failures caused by dirty or improper installation. Heat or freeze cracks to the block or heads. Defects or failures caused by failure to maintain proper coolant, fluid or lubrication levels or contaminated fluids, coolants, or lubricants. Defects or failures caused by fire, flood, vandalism, theft, collision, riots, acts of war, or acts of God. Defects or failures caused by rust or corrosion.

Heat Tabs or Serial Plate being removed. Excessive oil consumption and diminished performance. Condition: Remanufactured guarantee: 6 Months engine size: 1.5L fuel type: Diesel number of valves: 16 number of cylinders: 4-Cylinder performance : Non Turbo compression ratio : 23.1 bore diameter mm : 78.0 maximum horsepower ps : 44.3 maximum power kw : 26.1 maksimum power speed rpm : 3000 make : Kubota model : V1505 displacement : 1.5L maximum torque n m : 118.6 maximum torque speed rmp : 2000 dimension : 31 x 20 x 33 inch.